Difference between revisions of "Wiring: Safety Relay to Servo Module Fault Input"
(→I2T HMI Fault Masking) |
(→I2T HMI Fault Masking) |
||
| (6 intermediate revisions by one user not shown) | |||
| Line 5: | Line 5: | ||
<table cellpadding="15"> | <table cellpadding="15"> | ||
| − | <tr><td | + | <tr> |
| + | <td>[[image:warning.jpg|100px]]</td> | ||
<td width=300 bgcolor="#f0f0f0"> | <td width=300 bgcolor="#f0f0f0"> | ||
<font size=5>[[image:Gear_warning.jpg]] <b>WARNING!</b><br><br></font> | <font size=5>[[image:Gear_warning.jpg]] <b>WARNING!</b><br><br></font> | ||
| Line 16: | Line 17: | ||
<tr> | <tr> | ||
<td width=200> | <td width=200> | ||
| + | You can determine if the wiring on your bender is older by examining these points. If the points have wires labeled "2451", then your bender uses the older style of wire routing. To re-route the wiring to be compatible with newer benders, remove the 2451 wires from these points, then replace them with wires from the top row terminal strip point 16 of either module 192.168.0.201 or module 192.68.0.205. | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:cncbender_powerwire_toservofaults.jpg|500px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | ==I2T HMI Fault Masking== | ||
| + | |||
For this wire change to work properly, it is also important to ensure that the faults are not masked in the I2T setup. | For this wire change to work properly, it is also important to ensure that the faults are not masked in the I2T setup. | ||
| − | == | + | ==Tools/Parts Needed== |
| + | <table > | ||
| + | |||
| + | <tr> | ||
| + | <td width=100> | ||
| + | 14 Gauge THHN stranded wire | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:14awg_thhn_wire.jpg|200px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | <tr> | ||
| + | <td width=100> | ||
| + | Vinyl Insulate Terminal Pin for 14 gauge wire (See 159-1617 Kobiconn Terminals Pin Blue 16-14 at Mouser.com) | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:pinterminal.jpg|200px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | <tr> | ||
| + | <td width=100> | ||
| + | Jumper bar (Automationdirect.com DINnectors DN-82J10) | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:jumperbar_dn-82J10.jpg|200px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | <tr> | ||
| + | <td width=100> | ||
| + | Crimper for terminal pins, screw drivers, diagonal cutters for cutting the jumper bar | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:screwdrivers.jpg|200px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | |||
| + | <br><br> | ||
| + | |||
| + | ==Other Pages== | ||
| + | |||
| + | *Back to the [[CNC Bender]] Page | ||
| + | *Back to the [[CNC Bender Technical Notes]] Page | ||
Latest revision as of 18:19, 11 December 2009
Contents |
About the Wiring Standard
For increased safety, newer SMT benders are wired so that the servo modules fault inputs receive signal from the safety relay. The fault input points on the I2T servo modules are at points 8 and 10 on the bottom row of the terminal strips on these modules.
How to Determine Which Wiring Setup a Bender Uses
 |
|
|
You can determine if the wiring on your bender is older by examining these points. If the points have wires labeled "2451", then your bender uses the older style of wire routing. To re-route the wiring to be compatible with newer benders, remove the 2451 wires from these points, then replace them with wires from the top row terminal strip point 16 of either module 192.168.0.201 or module 192.68.0.205. |
|
I2T HMI Fault Masking
For this wire change to work properly, it is also important to ensure that the faults are not masked in the I2T setup.
Tools/Parts Needed
|
14 Gauge THHN stranded wire |
|
|
Vinyl Insulate Terminal Pin for 14 gauge wire (See 159-1617 Kobiconn Terminals Pin Blue 16-14 at Mouser.com) |
|
|
Jumper bar (Automationdirect.com DINnectors DN-82J10) |
|
|
Crimper for terminal pins, screw drivers, diagonal cutters for cutting the jumper bar |
|
Other Pages
- Back to the CNC Bender Page
- Back to the CNC Bender Technical Notes Page
