Difference between revisions of "Eaton Leonard"
| Line 35: | Line 35: | ||
[[image:vector_tube_data_center.jpg|200px]]<br> | [[image:vector_tube_data_center.jpg|200px]]<br> | ||
</td> | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | |||
| + | =About VTube-LASER to Premier, EL2000, Velog Communications= | ||
| + | ==[[image:Check.jpg|25px]] Complete Eaton Leonard Premier, EL2000, and Velog Setup Data inside VTube-LASER Bender Setup== | ||
| + | |||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=300 valign="top"> | ||
| + | VTube-LASER will now allow for the complete setup of all bender and setup data that can be stored in a Premier, EL2000, or Velog control.<br><br> | ||
| + | The Eaton Leonard values are never lost because this data is now stored inside each VTube-LASER project file. <br><br> | ||
| + | Press the new "'''Additional Bender Data'''" button at the top of the Bender Setup screen, and VTube will now load the new Eaton Leonard Setup window shown (see the second image).<br><br> | ||
| + | |||
| + | ===YBC Velocity, Function, Stop, and C Last Included=== | ||
| + | This data includes all the part setup data and all the data that is included in each YBC row, including these data columns:<br><br> | ||
| + | |||
| + | * Y | ||
| + | * Y Velocity | ||
| + | * Y Function | ||
| + | * Y Stop | ||
| + | * B | ||
| + | * B Velocity | ||
| + | * B Function | ||
| + | * B Stop | ||
| + | * C | ||
| + | * C Velocity | ||
| + | * C Function | ||
| + | * C Stop | ||
| + | * C Last | ||
| + | <br><br> | ||
| + | Click on the image on the right so see a close-up of this screen.<br><br><br> | ||
| + | |||
| + | ===YBC Data Automatically Synchronized with Blue Column LRA Data in the Parent Window=== | ||
| + | The YBC data in this new Eaton Leonard Setup window is always synchronized with the blue columns in the parent VTube Bender Setup window.<br><br> | ||
| + | Change the data in either window, and the corresponding data in the other window will automatically change.<br><br> | ||
| + | |||
| + | ===Use Either Inches or Millimeters=== | ||
| + | The screen allows you to switch between Inches and Millimeters and back again with the press of a single button. | ||
| + | |||
| + | |||
| + | |||
| + | * See [[Eaton Leonard]] | ||
| + | <br> | ||
| + | <br> | ||
| + | |||
| + | </td> | ||
| + | |||
| + | <td valign="top"> | ||
| + | [[image:vtube-laser_bendersetup_eatonleonard_button.png|600px]]<br><br> | ||
| + | [[image:vtube-laser_eatonleonard_setupwindow.png|600px]]<br><br> | ||
| + | [[image:vtube-laser_bendersetup_eatonleonard_synchronized.png|600px]]<br><br> | ||
| + | </td> | ||
| + | |||
</tr> | </tr> | ||
</table> | </table> | ||
Revision as of 04:29, 1 December 2016
|
Eaton Leonard produces tube bending machines.
|
|
|
Our VTube-LASER software can communicate with all four bender types above. The Lightspeed requires a network connection. The other three require our Benderlink Ethernet Module electronics. (VTube-LASER uses a FARO arm to measure tube shapes.) |
|
|
Most of our Benderlink packages are compatible with the Vector Tube Data Center. Our Benderlink Ethernet Module is also compatible with the Vector. |
|
Contents |
About VTube-LASER to Premier, EL2000, Velog Communications
Complete Eaton Leonard Premier, EL2000, and Velog Setup Data inside VTube-LASER Bender Setup
|
VTube-LASER will now allow for the complete setup of all bender and setup data that can be stored in a Premier, EL2000, or Velog control. YBC Velocity, Function, Stop, and C Last IncludedThis data includes all the part setup data and all the data that is included in each YBC row, including these data columns:
YBC Data Automatically Synchronized with Blue Column LRA Data in the Parent WindowThe YBC data in this new Eaton Leonard Setup window is always synchronized with the blue columns in the parent VTube Bender Setup window. Use Either Inches or MillimetersThe screen allows you to switch between Inches and Millimeters and back again with the press of a single button.
|
|
