Difference between revisions of "VTube-LASER Videos for HEXAGON ROMER"
(→Version 3.0) |
(→Version 3.0) |
||
| Line 20: | Line 20: | ||
===Version 3.0=== | ===Version 3.0=== | ||
| + | |||
| + | ====Video 20200514: How to Change Languages in VTube==== | ||
| + | <table width=700> | ||
| + | <tr> | ||
| + | <td width=300> | ||
| + | This video shows how to change languages in the VTube-LASER and VTube-STEP user interface. | ||
| + | |||
| + | <td width=200> | ||
| + | [[image:20200514_changelanguges_video.png|300px]]<br> | ||
| + | </td> | ||
| + | <td width=300> | ||
| + | * View [https://www.advancedtubular.com/vtube-laser/vtl_v3_change_languages.mp4 MP4] | ||
| + | |||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | <br><br> | ||
====Video 20200331: VTube UNIVERSITY Training Video: Verify a HEXAGON Arm with a Precision Cylinder Bar==== | ====Video 20200331: VTube UNIVERSITY Training Video: Verify a HEXAGON Arm with a Precision Cylinder Bar==== | ||
Revision as of 16:19, 14 May 2020
|
See a list of VTube-LASER videos for ROMER Absolute Arms from HEXAGON on this page.
|
|
Version 3.0
Video 20200514: How to Change Languages in VTube
|
This video shows how to change languages in the VTube-LASER and VTube-STEP user interface. |
|
|
Video 20200331: VTube UNIVERSITY Training Video: Verify a HEXAGON Arm with a Precision Cylinder Bar
|
This is a VTube University video that shows how to quickly verify a HEXAGON ScanArm with VTube-LASER and a precision cylinder bar. |
|
Video 20200320: VTube UNIVERSITY Training Video: End Scans
|
This video is a VTube University video designed to show how to effectively end scan a tube using VTube-LASER. |
|
Video 20200225: How to manually setup the Ethernet port for HEXAGON RDS connection
|
This video shows a corrections loop between VTube-LASER and an OMCG wire bender. |
|
|
You can manually setup the Ethernet port following the steps in this short video. |
|
|
Video 20200206: How to Switch from Probe to LASER with HEXAGON RA8 Arms
|
Switching from probe to laser is easy with the three-way toggle button. (Using a HEXAGON RA8 ScanArm) |
|
Version 2.9.21
Video 20200114: How to Use VTube-LASER Corner Profile Measure Process for Different Tube Profiles
|
See how to use VTube-LASER Corner Profile measurement for PROFILE, SQUARE, RECTANGULAR, and EXTRUDED shapes - with either the LASER or the BALL PROBE. (Using a HEXAGON 8325 ScanArm) |
|
Video 107: Corrections Loop with SOCO Beckhoff Controls
|
This demo video shows how VTube-LASER performs corrections loop communications with SOCO Beckhoff controls. |
|
Version 2.9.19
Video 104: Demo of VTube-LASER Measuring from 2mm to 450mm Tube and Pipe + Square
|
This demo video shows the wide range of tube, pipe, wire, string types that VTube-LASER can scan with a laser scanner arm. |
|
Video 103: VTube-LASER "Timer Accept" Feature Cuts Button Press Counts in Half
|
This video shows how the TIMER ACCEPT button can decrease your button presses during UniScan tube measuring by half. |
|
Version 2.9.18
Video 100: How To Calculate the Centerline Radius in a Measured 180-degree Bend
|
This video shows how to use the Dimension Control window to calculate the true radius of a 180-degree bend. |
|
|
Video 99: See VTube-LASER Reverse Engineer a RZR Side by Side Custom Tube Assembly using a HEXAGON RA8 Arm
|
This video shows Michael Cone using VTube-LASER to reverse engineer a custom 8 tube assembly for a RZR Side by Side in 8 minutes - including sending the part to SOLIDWORKS. |
|
Video 98: About the Small Diameter Warning
|
This video shows how Small Diameter Warning works along with its setup. |
|
Video 96: VTube-STEP and VTube-LASER New Radius Features
|
See the new radius features in this video. In Part Setup:
|
|
Video 95: VTube-LASER Communicating with BendPro G2 on an RbSA Industrial BOOST Trainer
Michael Cone simulates a corrections loop between VTube-LASER v2.9.18 and BendPro G2 on an RbSA Industrial BOOST trainer.
|
|
Version 2.9.17
Video 94: Five Major Enhancements to VTube-LASER Version 2.9.17 - FEATURING the HEXAGON ABSOLUTE ARM
Michael Cone shows 5 major new features in VTube-LASER v2.9.17. (Released on December 30, 2018).
|
|
Version 2.9.16
Video 90: How to Attach and Use the ROMER Absolute 8-series Scanner in VTube-LASER
This is a video where Michael Cone shows how to attach and use the 8-series style arm scanner with VTube-LASER.
|
|
Version 2.9.10
Video 86: VTube-LASER's LASER SCAN FILTER SOUND
This is a short video that shows how the Laser Scan Filter sound helps you know when all laser scan data is removed by the scan filters.
|
|
Video 84: Measuring Convoluted Tube and Wire with VTube-LASER
This video shows VTube-LASER's ability to measure extremely convoluted parts with a ROMER Absolute Arm with Integrated Scanner. This wire part wraps back on itself in several places, making it very challenging. Because VTube-LASER has scanning filters, it can measure this part with a wider laser stripe.
|
|
Version 2.9.4
Video 78: VTube-LASER Corrects an SMT Bender Using a ROMER Absolute Arm
This video demonstrates the correction process between VTube-LASER and an SMT remanufactured VB300 bender. We use a ROMER Absolute Arm with integrated scanner in this video.
|
|
Version 2
Video 2: SCANNING SPEED TEST ON TWO TYPES OF TUBES
|
This video shows speed tests on two very different kinds of tube shapes:
|
|
Video 1: INTRODUCING VTUBE-LASER MEASURING WITH A ROMER ABSOLUTE ARM
| As of November 1, 2017, VTube-LASER can measure tubes with ROMER Absolute Arms from HEXAGON. This video shows a measurement of a tube using a 3.5 meter ROMER arm. |
|
Other Pages
- Back to VTube-LASER
