Difference between revisions of "VTube-LASER Videos for HEXAGON ROMER"
(→Video 20200609: How to Use Multiple Versions of the Same Part in One Project) |
(→Version 3.0) |
||
| Line 21: | Line 21: | ||
===Version 3.0=== | ===Version 3.0=== | ||
| + | |||
| + | ====Video 20200709: Real-time Overall Scan Scores Build Confidence==== | ||
| + | <table width=700> | ||
| + | <tr> | ||
| + | <td width=300> | ||
| + | This video shows how VTube-LASER scan scoring system helps users know they are measuring well. | ||
| + | |||
| + | <td width=200> | ||
| + | [[image:20200709_scanscore_video.png|300px]]<br> | ||
| + | </td> | ||
| + | <td width=300> | ||
| + | * View [https://www.advancedtubular.com/vtube-laser/vtl_v3_realtime_scanscore.mp4 MP4] | ||
| + | |||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
Revision as of 03:18, 10 July 2020
|
See a list of VTube-LASER videos for ROMER Absolute Arms from HEXAGON on this page.
|
|
Version 3.0
Video 20200709: Real-time Overall Scan Scores Build Confidence
|
This video shows how VTube-LASER scan scoring system helps users know they are measuring well. |
|
|
Video 20200609: How to Use Multiple Versions of the Same Part in One Project
|
This video shows how to use Assembly to create multiple versions of the same part in one project. Each version can then be used to measure the part at various stages of the fabrication process. |
|
|
Video 20200515: How Import 180-degree Bend Models
|
This video shows how to import models with 180-degree bends. |
|
|
Video 20200514: How to Change Languages in VTube
|
This video shows how to change languages in the VTube-LASER and VTube-STEP user interface. |
|
|
Video 20200331: VTube UNIVERSITY Training Video: Verify a HEXAGON Arm with a Precision Cylinder Bar
|
This is a VTube University video that shows how to quickly verify a HEXAGON ScanArm with VTube-LASER and a precision cylinder bar. |
|
Video 20200320: VTube UNIVERSITY Training Video: End Scans
|
This video is a VTube University video designed to show how to effectively end scan a tube using VTube-LASER. |
|
Video 20200225: How to manually setup the Ethernet port for HEXAGON RDS connection
|
This video shows a corrections loop between VTube-LASER and an OMCG wire bender. |
|
|
You can manually setup the Ethernet port following the steps in this short video. |
|
|
Video 20200206: How to Switch from Probe to LASER with HEXAGON RA8 Arms
|
Switching from probe to laser is easy with the three-way toggle button. (Using a HEXAGON RA8 ScanArm) |
|
Version 2.9.21
Video 20200114: How to Use VTube-LASER Corner Profile Measure Process for Different Tube Profiles
|
See how to use VTube-LASER Corner Profile measurement for PROFILE, SQUARE, RECTANGULAR, and EXTRUDED shapes - with either the LASER or the BALL PROBE. (Using a HEXAGON 8325 ScanArm) |
|
Video 107: Corrections Loop with SOCO Beckhoff Controls
|
This demo video shows how VTube-LASER performs corrections loop communications with SOCO Beckhoff controls. |
|
Version 2.9.19
Video 104: Demo of VTube-LASER Measuring from 2mm to 450mm Tube and Pipe + Square
|
This demo video shows the wide range of tube, pipe, wire, string types that VTube-LASER can scan with a laser scanner arm. |
|
Video 103: VTube-LASER "Timer Accept" Feature Cuts Button Press Counts in Half
|
This video shows how the TIMER ACCEPT button can decrease your button presses during UniScan tube measuring by half. |
|
Version 2.9.18
Video 100: How To Calculate the Centerline Radius in a Measured 180-degree Bend
|
This video shows how to use the Dimension Control window to calculate the true radius of a 180-degree bend. |
|
|
Video 99: See VTube-LASER Reverse Engineer a RZR Side by Side Custom Tube Assembly using a HEXAGON RA8 Arm
|
This video shows Michael Cone using VTube-LASER to reverse engineer a custom 8 tube assembly for a RZR Side by Side in 8 minutes - including sending the part to SOLIDWORKS. |
|
Video 98: About the Small Diameter Warning
|
This video shows how Small Diameter Warning works along with its setup. |
|
Video 96: VTube-STEP and VTube-LASER New Radius Features
|
See the new radius features in this video. In Part Setup:
|
|
Video 95: VTube-LASER Communicating with BendPro G2 on an RbSA Industrial BOOST Trainer
Michael Cone simulates a corrections loop between VTube-LASER v2.9.18 and BendPro G2 on an RbSA Industrial BOOST trainer.
|
|
Version 2.9.17
Video 94: Five Major Enhancements to VTube-LASER Version 2.9.17 - FEATURING the HEXAGON ABSOLUTE ARM
Michael Cone shows 5 major new features in VTube-LASER v2.9.17. (Released on December 30, 2018).
|
|
Version 2.9.16
Video 90: How to Attach and Use the ROMER Absolute 8-series Scanner in VTube-LASER
This is a video where Michael Cone shows how to attach and use the 8-series style arm scanner with VTube-LASER.
|
|
Version 2.9.10
Video 86: VTube-LASER's LASER SCAN FILTER SOUND
This is a short video that shows how the Laser Scan Filter sound helps you know when all laser scan data is removed by the scan filters.
|
|
Video 84: Measuring Convoluted Tube and Wire with VTube-LASER
This video shows VTube-LASER's ability to measure extremely convoluted parts with a ROMER Absolute Arm with Integrated Scanner. This wire part wraps back on itself in several places, making it very challenging. Because VTube-LASER has scanning filters, it can measure this part with a wider laser stripe.
|
|
Version 2.9.4
Video 78: VTube-LASER Corrects an SMT Bender Using a ROMER Absolute Arm
This video demonstrates the correction process between VTube-LASER and an SMT remanufactured VB300 bender. We use a ROMER Absolute Arm with integrated scanner in this video.
|
|
Version 2
Video 2: SCANNING SPEED TEST ON TWO TYPES OF TUBES
|
This video shows speed tests on two very different kinds of tube shapes:
|
|
Video 1: INTRODUCING VTUBE-LASER MEASURING WITH A ROMER ABSOLUTE ARM
| As of November 1, 2017, VTube-LASER can measure tubes with ROMER Absolute Arms from HEXAGON. This video shows a measurement of a tube using a 3.5 meter ROMER arm. |
|
Other Pages
- Back to VTube-LASER
