Difference between revisions of "Benderlink for Pines"
From ATTWiki
(→Other Pages) |
(→TS-2000 Control to Vector 1 Laservision) |
||
| Line 19: | Line 19: | ||
| [[image:Ts-2000.jpg|100px]] | | [[image:Ts-2000.jpg|100px]] | ||
| The software installs directly on the operator station of the Pines TS-2000 controls. It is designed to interact directly with the control. The designer of the TS-2000 included a "Laservision" button that loads and calls to Benderlink for Pines.<br><br> | | The software installs directly on the operator station of the Pines TS-2000 controls. It is designed to interact directly with the control. The designer of the TS-2000 included a "Laservision" button that loads and calls to Benderlink for Pines.<br><br> | ||
| − | The protocol used is the Velog/El-2000/Premier protocol - so the software is compatible with Eaton Leonard Vector Laservision out of the box | + | The protocol used is the Velog/El-2000/Premier protocol - so the software is compatible with Eaton Leonard Vector Laservision out of the box. |
| − | + | ||
| [[Image:EL Laservision Tube Data Center.jpg|400px]] | | [[Image:EL Laservision Tube Data Center.jpg|400px]] | ||
| + | |} | ||
| + | |||
| + | |||
| + | |||
| + | =Benderlink Ethernet Module= | ||
| + | |||
| + | |||
| + | {| border="0" cellpadding="5" cellspacing="0" align="none" width=700 | ||
| + | |- | ||
| + | | [[image:Ts-2000.jpg|100px]] | ||
| + | | The software uses the [[Benderlink Ethernet Module for PINES to Vector]] to connect to any Vector. | ||
| + | | [[image:Blinklines2vector_pdfimage.jpg|400px]] | ||
|} | |} | ||
Revision as of 13:28, 2 May 2008
Contents |
About
| Benderlink for Pines is software that connects PINES TS-2000 controls with Eaton Leonard Vector Laservision measuring centers. It essentially makes a TS-2000 control appear to be an Eaton Leonard PREMIER control to a Vector Laservision measuring center. |
|
TS-2000 Control to Vector 1 Laservision
|
The software installs directly on the operator station of the Pines TS-2000 controls. It is designed to interact directly with the control. The designer of the TS-2000 included a "Laservision" button that loads and calls to Benderlink for Pines. The protocol used is the Velog/El-2000/Premier protocol - so the software is compatible with Eaton Leonard Vector Laservision out of the box. |
|
Benderlink Ethernet Module
|
|
The software uses the Benderlink Ethernet Module for PINES to Vector to connect to any Vector. | 
|
Version 2.0 - Plug-And-Play Compatible with Vector Laservision
| Version 2 is designed to communicate using the standard Eaton Leonard Velog, EL-2000, and Premier protocol. This protocol is available on every Eaton Leonard measuring center.
|
|
Version 1.0 (Obsolete)
| Version 1 of Benderlink for Pines communicated with Laservisions using the ATT protocol. The ATT protocol was a special protocol that required customers to purchase and install an upgrade to the Vector Laservision. Eaton Leonard referred to this as a "Competitive Bender Interface" because it was designed to grant competitors the right to use the measuring center through license charges.
|
|
Version Updates
| Screen Shot | Date Released | Link to Page | New Features |
|
April 28, 2008 | Benderlink for Pines 2.0 |
|
Other Pages
Back to the Benderlink Page
Hardware for making the connection: Benderlink Ethernet Module for PINES to Vector
