Difference between revisions of "VTube-LASER Videos"
(→Video Topic: Effective End Scans) |
(→Video Topic: Effective End Scans) |
||
| Line 23: | Line 23: | ||
===Version 1.80.1 - December 14, 2012=== | ===Version 1.80.1 - December 14, 2012=== | ||
| + | |||
| + | ====Video Topic: Repeatability Test for Surface Coated Aluminum==== | ||
| + | <table width=600> | ||
| + | |||
| + | <tr> | ||
| + | <td width=200> | ||
| + | This demonstrates a quick repeatability test of a surface-coated aluminum tube.<br><br>Note: This video has no narration. | ||
| + | </td> | ||
| + | <td width=200> | ||
| + | [[image:VTube-STEP_1.80.1_repeatability_surfacecoat_alum.jpg|200px]]<br> | ||
| + | </td> | ||
| + | <td width=200> | ||
| + | * View on [http://youtu.be/syTi5dzi0PE YouTube] | ||
| + | * View [http://www.advancedtubular.com/vtube-laser/vtube-1.80-surfacecoat-fixedexposure-test.mp4 MP4] | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | |||
====Video Topic: Effective End Scans==== | ====Video Topic: Effective End Scans==== | ||
Revision as of 17:23, 14 December 2012
|
|
|
Contents |
Version 1.80.1 - December 14, 2012
Video Topic: Repeatability Test for Surface Coated Aluminum
|
This demonstrates a quick repeatability test of a surface-coated aluminum tube. |
|
Video Topic: Effective End Scans
|
This demonstrates the different end scan techniques for measuring tube. |
|
Version 1.80 - December 8, 2012
Video Topic: Effective highly reflective aluminum scanning
|
This is a proof-of-concept video for a 1/2" highly reflective aluminum tube. The goal is to demonstrate repeatability better than 300 microns. |
|
Version 1.80 - November 23, 2012
|
How to extract a tube centerline of demo part 2 with VTube-STEP version 1.80. Note that this part has a 180 degree bend - which requires special steps for import anc calculation. |
|
Version 1.76.4 - May 15, 2012
|
How to measure a straight tube. |
|
|
How to use Measured tube data to create Master tube data. |
Version 1.76.3 - April 2, 2012
|
How to setup the Scanner Control to measuring tubes with the laser probe. |
Version 1.76 - March 15, 2012
|
Unbending a tube with coping at either end. |
Version 1.75 - February 2012
- View on YouTube - Measuring a small 8mm tube that bends back on itself
- Download MP4 - Measuring a small 8mm tube that bends back on itself
- View on YouTube - Measuring a highly deformed 6 inch tube for hydroforming
- Download MP4 - Measuring a highly deformed 6 inch tube for hydroforming
- View on YouTube - Reverse engineering a highly reflective part with a 180 degree bend
- Download MP4 - Reverse engineering a highly reflective part with a 180 degree bend
- View on YouTube - How to compare two Supravision project files in VTube-LASER
- Download MP4 - How to compare two Supravision project files in VTube-LASER
- View on YouTube - STEP Mode Solid Model Import of Large Diameter Tube
- Download MP4 - STEP Mode Solid Model Import of Large Diameter Tube
- View on YouTube - How to demonstrate VTube-LASER importing a CAD model.
- Download MP4 - How to demonstrate VTube-LASER importing a CAD model.
- View on YouTube - How to demonstrate measuring the VTube-LASER demo tube.
- Download MP4 - How to demonstrate measuring the VTube-LASER demo tube.
Older Versions
- v1.73 Measuring HVAC parts with 180 degree bends
- v1.57 Reverse Engineering a Tube
- v1.57 Recall MASTER Bender Data from Benders
- v1.53 Reverse Engineering SPEED TEST Video
- Measure 1/2" tube
- Start a new 1/4" tube project with master data
Other Pages
- Back to VTube-LASER
