Difference between revisions of "VTube-LASER v1.91"

Revision 1.91

• Back to VTube-STEP
• Back to VTube-STEP Revisions
• Back to VTube Software Updates (for LASER Mode)
• Back to VTube-LASER

The new Leapfrog feature allows you to measure any length of tube by measuring three or more magnetic cones, leaping the cones with the FARO arm, then measuring the cones again - then continuing measuring from where you left off before the leap.

A leap can occur at any point during any tube measurement.

Leapfrog moves are more accurate than using the "Move Tube" command because they rely on more precise conical seats.

• Tolerances are now PLUS or MINUS rather than just a single value.
  
  
• The "Out of Tolerance" value can now be displayed alongside the deviation value.
  
  
• The "Out of Tolerance" value is color-coded for pass/fail.
  
  
• The new expanded grid (see below) shows the MASTER and ALIGNED XYZ intersection points.
  
  

The data shown on the right is from the new Expanded Grid (see "Expanded Grid" section below).

• The new expanded grid (see below) shows the MASTER and ALIGNED XYZ tangent points.
  
  
• The "Out of Tolerance" value can now be displayed alongside the deviation value.
  
  
• The "Out of Tolerance" value is color-coded for pass/fail.
  
  

The data shown on the right is from the new Expanded Grid (see "Expanded Grid" section below).

The XYZ Intersection deviation and the XYZ Tangent point deviation values can now be displayed in the Expanded Grid window.

• Show all the possible data, including XYZ master and XYZ aligned data in one wide grid.
  
  
• Copy the grid to the clipboard.
  
  
• Automatically send the grid to Word or Excel if they are available on your system.
  
  
• The tolerance cells can also be edited in the expanded grid window.
  
  

The new XYZ Intersection deviation values are included in reports:

1. plus tolerance values
   
2. minus tolerance values
   
3. out of tolerance values
   

Displayed Deviation Values Corrected

Previous deviation values used for decision making were incorrectly high. This has been repaired.

Alignment Engine "Seeking Precision Level" Display

The progress window shows the goal precision level the engine is seeking for. For example, if the Automatic Alignment Stop value is 0.75 and the tolerance is 0.059, then the progress window will show "Alignment Engine seeking precision level of: 0.044". The goal precision is used in decision making during automatic alignments. If all tangent deviations are equal to or less than the goal precision, then alignment stops immediately. This makes automatic alignment much faster potentially.

Alignment Engine "Maximum Iterations" Display and Logic

The current iteration and possible maximum iterations for finding the best alignment is now displayed in the progress window.

• The "Maximum Iterations" is the number of alignments that VTube has found that may want to compare.
  
  
• If 100 iterations passes with no improvement to the Average Tangent Deviation" and the Highest Tangent Deviation values, then alignment stops immediately to save time.
  
  

This new measurement complete dialog gives you more choices than before. It no longer assumes that you want to use the current default alignment method.

You can choose from any one of the available alignment methods in this dialog.

The Inspection Data recalculate alignment button now displays the currently selected alignment method.

This fixes a problem where users had to guess the alignment method when recalculating the measured to master alignment.

The Automatic Alignment Stop value in the Inspection Data / Alignment menu is renamed to make it more understandable: "Automatic Alignment Stop at Deviation Multiplied Against..." is the new name.

• VTube now communicates with the older Eaton Leonard Premier, EL2000, and Ve-log controls.
  
  

• We added a second type of report per a customer spec.
• The reports are now built to both comma delimted and tab delimited files.
• The reports can be sent directly to Excel.
  
  

Load the batch reporter in the Report menu of either STEP mode of LASER mode:

This is a sample report file:

If the batch reporter finds files with 0 or negative length straights, then it will issue a WARNING at the end of the report log and create a second report file containing a list of all the project files with these lengths:

• IMPORTANT Fix to bug in END TRIM/EXTEND distances in the inspection reports. Sometimes the direction would be inverted. This has been resolved.
  
  
• Now you can click on the scanner control labels to load the FARO Scanner control window.
  
  
• VTube will automatically set the wall thickness to 0.001 inches or 0.025 millimeters when the value is set to zero during VTube-STEP solid model centerline calculations.
  
  
• Now you can press the Enter key to close the information dialog.
  
  
• The FARO calibration dialogs now show either Inches or Millimeters
  
  
• Comments display in a dialog during project load
  
  
• The Scanner Control settings are stored in VTube project files. In order for the scanner setup to be transferred into the arm, it is necessary to pull the arm from the cradle before the setup is transferred. VTube will ask you to move the arm when it is important.
  
  
• The USB FARO driver icon is now displayed in the toolbar at the bottom of Windows.
  
  
• The "Clear text" button in the editor box works again.