Difference between revisions of "Benderlink Ethernet Module"
(→Other Applications) |
(→Inside the Module) |
||
| Line 93: | Line 93: | ||
*The Current Loop board is in the upper right corner.<br><br> | *The Current Loop board is in the upper right corner.<br><br> | ||
*The Ethernet Serial Device Server is the black box on the bottom.<br><br> | *The Ethernet Serial Device Server is the black box on the bottom.<br><br> | ||
| − | *The power supply is on the upper left. | + | *The larger (and much improved) power supply is on the upper left. |
</td> | </td> | ||
<td> | <td> | ||
| Line 103: | Line 103: | ||
<br><br> | <br><br> | ||
| + | |||
===Other Applications=== | ===Other Applications=== | ||
Revision as of 21:06, 5 January 2016
Put SERIAL Port Benders on a Wireless or Wired NETWORK at Extended Distances
|
The module connects any bender or measuring center devices through your Ethernet network to a bender that normally connects using only standard RS-232 signals. It gives your bender or measuring center access to a virtual COM port anywhere on the network in your building. Distance limitations are removed with this protocol. We have WiFi (wireless) and WIRED TCP/IP models. |
|
Connect to EL Vector Tube Data Centers Using Current Loop Electronics
|
The module can even be equipped with our version of the Eaton Leonard current loop boards (our own model called the CB-EL1) to allow for 100% compatible Eaton Leonard legacy protocol through the network for connection to an EL Vector Tube Data Center |
|
Connect VTube-LASER to Eaton Leonard Benders using Current Loop Electronics
|
The module, equipped with our current loop electronics, can be used to connect the FARO arm with VTube-LASER software to Eaton Leonard benders. See VTube-LASER to Eaton Leonard Benders |
|
Cabling
| This is a module with cables in place. Three cables are attached to the wired version. A fourth wireless antenna cable is attached for wireless version. |
|
PINES TS-2000 to Eaton Leonard Tube Data Center
|
This is a single port Benderlink Ethernet Module that connected a TS-2000 (Pines) control to an Eaton Leonard Vector 1 measuring center. |
|
|
This is a more compact and newer verison of the Benderlink Ethernet Module that is designed for connection to an Eaton Leonard Vector Laservision measuring center for conversion through Benderlink for COMCO. |
|
Inside the Module
|
This image is the internal view of an older module.
|
|
|
This is the newer and more compact version of the module's internal setup.
|
|
Other Applications
| Bender | Description | |
|---|---|---|
| SMT Bender | We use a Benderlink Module to make the SMT act like a Premiere bender control to an Eaton Leonard Vector measuring center. | |
| PINES TS-2000 | Using Benderlink for Pines - Add a module to a Vector Tube Data Center to enable a network connection through a current-loop module directly into the standard Vector bender port. | |
| BLM VGP | Using Benderlink for BLM - Add a module to Vector Tube Data Center to enable a network connection through a current-loop module directly into the standard Vector bender port. | |
| ROMER to Eaton Leonard Bender | Add a module to any Eaton Leonard bender and make it wireless. | |
| CHIYODA | Add this module to a Chiyoda to allow it to communicate over the network from its RS-232 port. | |
| KEINS | Add this module to a KEINS to allow it to communicate over the network from its RS-232 port. | |
| MiiC | Works with a MiiC to place it on the network (See Benderlink for MiiC) | |
PDF DataSheets
|
|
Download a DataSheet for Benderlink Ethernet Module for Eaton Leonard
|
