Difference between revisions of "Benderlink Ethernet Module"
(→PINES TS-2000 to Eaton Leonard Tube Data Center) |
(→Inside the Module) |
||
| Line 79: | Line 79: | ||
===Inside the Module=== | ===Inside the Module=== | ||
<table> | <table> | ||
| + | |||
| + | <tr> | ||
| + | <td width=300> | ||
| + | This is the newer and more compact version of the Benderlink Ethernet Module that is designed for connection to an Eaton Leonard Vector Laservision measuring center for conversion through Benderlink for COMCO. | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:BenderlinkEternetModuleEL_External1.png|300px]] | ||
| + | </td> | ||
| + | </tr> | ||
<tr> | <tr> | ||
Revision as of 21:12, 5 January 2016
Put SERIAL Port Benders on a Wireless or Wired NETWORK at Extended Distances
|
The module connects any bender or measuring center devices through your Ethernet network to a bender that normally connects using only standard RS-232 signals. It gives your bender or measuring center access to a virtual COM port anywhere on the network in your building. Distance limitations are removed with this protocol. We have WiFi (wireless) and WIRED TCP/IP models. |
|
Connect to EL Vector Tube Data Centers Using Current Loop Electronics
|
The module can even be equipped with our version of the Eaton Leonard current loop boards (our own model called the CB-EL1) to allow for 100% compatible Eaton Leonard legacy protocol through the network for connection to an EL Vector Tube Data Center |
|
Connect VTube-LASER to Eaton Leonard Benders using Current Loop Electronics
|
The module, equipped with our current loop electronics, can be used to connect the FARO arm with VTube-LASER software to Eaton Leonard benders. See VTube-LASER to Eaton Leonard Benders |
|
Cabling
| This is a module with cables in place. Three cables are attached to the wired version. A fourth wireless antenna cable is attached for wireless version. |
|
PINES TS-2000 to Eaton Leonard Tube Data Center
|
This is a single port Benderlink Ethernet Module that connected a TS-2000 (Pines) control to an Eaton Leonard Vector 1 measuring center. |
|
|
This image is the internal view of an older module.
|
|
Inside the Module
|
This is the newer and more compact version of the Benderlink Ethernet Module that is designed for connection to an Eaton Leonard Vector Laservision measuring center for conversion through Benderlink for COMCO. |
|
|
This is the newer and more compact version of the module's internal setup.
|
|
Other Applications
| Bender | Description | |
|---|---|---|
| SMT Bender | We use a Benderlink Module to make the SMT act like a Premiere bender control to an Eaton Leonard Vector measuring center. | |
| PINES TS-2000 | Using Benderlink for Pines - Add a module to a Vector Tube Data Center to enable a network connection through a current-loop module directly into the standard Vector bender port. | |
| BLM VGP | Using Benderlink for BLM - Add a module to Vector Tube Data Center to enable a network connection through a current-loop module directly into the standard Vector bender port. | |
| ROMER to Eaton Leonard Bender | Add a module to any Eaton Leonard bender and make it wireless. | |
| CHIYODA | Add this module to a Chiyoda to allow it to communicate over the network from its RS-232 port. | |
| KEINS | Add this module to a KEINS to allow it to communicate over the network from its RS-232 port. | |
| MiiC | Works with a MiiC to place it on the network (See Benderlink for MiiC) | |
| YLM | Works with a YLM to connect to an EL Vector Laservision Measureing Center (See Benderlink for YLM) | |
| COMCO | Works with a COMCO to connect to an EL Vector Laservision (See Benderlink for COMCO) | |
PDF DataSheets
|
|
Download a DataSheet for Benderlink Ethernet Module for Eaton Leonard
|
