Difference between revisions of "Benderlink Ethernet Module"
(→Connect VTube-LASER to Eaton Leonard Premier Benders using Current Loop Electronics) |
(→Connect VTube-LASER to Eaton Leonard Premier Benders using Current Loop Electronics) |
||
| Line 25: | Line 25: | ||
<td> | <td> | ||
[[image:vector_tube_data_center_sensor.jpg]] | [[image:vector_tube_data_center_sensor.jpg]] | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
Revision as of 17:19, 2 December 2016
Put SERIAL Port Benders on a Wireless or Wired NETWORK at Extended Distances
|
The module connects any bender or measuring center devices through your Ethernet network to a bender that normally connects using only standard RS-232 signals. It gives your bender or measuring center access to a virtual COM port anywhere on the network in your building. Distance limitations are removed with this protocol. We have WiFi (wireless) and WIRED TCP/IP models. |
|
Connect to EL Vector Tube Data Centers Using Current Loop Electronics
|
The module can even be equipped with our version of the Eaton Leonard current loop boards (our own model called the CB-EL1) to allow for 100% compatible Eaton Leonard legacy protocol through the network for connection to an EL Vector Tube Data Center |
|
Cabling
This is a module with cables in place. Three cables are attached to the wired version. A fourth wireless antenna cable is attached for wireless version.
|
|
PINES TS-2000 to Eaton Leonard Tube Data Center
|
This is a single port Benderlink Ethernet Module that connected a TS-2000 (Pines) control to an Eaton Leonard Vector 1 measuring center. |
|
|
This is the internal setup.
|
|
Module for EL Vector Laservision to Benderlink for COMCO
|
This is the newer and more compact version of the Benderlink Ethernet Module that is designed for connection to an Eaton Leonard Vector Laservision measuring center for conversion through Benderlink for COMCO. |
|
|
This is internal setup.
|
|
Other Applications
| Bender | Description | |
|---|---|---|
| SMT Bender | We use a Benderlink Module to make the SMT act like a Premiere bender control to an Eaton Leonard Vector measuring center. | |
| PINES TS-2000 | Using Benderlink for Pines - Add a module to a Vector Tube Data Center to enable a network connection through a current-loop module directly into the standard Vector bender port. | |
| BLM VGP | Using Benderlink for BLM - Add a module to Vector Tube Data Center to enable a network connection through a current-loop module directly into the standard Vector bender port. | |
| ROMER to Eaton Leonard Bender | Add a module to any Eaton Leonard bender and make it wireless. | |
| CHIYODA | Add this module to a Chiyoda to allow it to communicate over the network from its RS-232 port. | |
| KEINS | Add this module to a KEINS to allow it to communicate over the network from its RS-232 port. | |
| MiiC | Works with a MiiC to place it on the network (See Benderlink for MiiC) | |
| YLM | Works with a YLM to connect to an EL Vector Laservision Measureing Center (See Benderlink for YLM) | |
| COMCO | Works with a COMCO to connect to an EL Vector Laservision (See Benderlink for COMCO) | |
PDF DataSheets
|
|
Download a DataSheet for Benderlink Ethernet Module for Eaton Leonard
|
