Difference between revisions of "VTube Communication for CRIPPA MPF"

This page describes the setup and use of the VTube to CRIPPA MPF file communications for older CRIPPA benders that do not have the SVNET protocol.

VTube-STEP can build CRIPPA MPF files that can be loaded into CRIPPA controls

VTube-LASER, can build and correct data in CRIPPA MPF files for bender corrections.

500px

1. Connect the CRIPPA bender to the network using a standard Ethernet cable.
   
   
2. Setup the data folders so that they are a shared network location on your network. These folders will contain MPF files.
   
   

1. Enter the VTube System Options menu.
   
   
2. Enter the Measure 2 tab menu.
   
   
3. Enter the Setup Benderlink Network menu.
   
   

1. Choose an unused row in the grid for a new CRIPPA bender setup. (Click on the image at the right to see a zoomed image.)
   
   
2. Assign a bender name that will help operators identify which bender this is. This text will be displayed at the top of the Bender Setup menu.
   
   
3. Assign the CRIPPA MPF protocol.
   
   
4. Enter the path to the shared drive or folder in the NetPath field. This path should point to the folder that contains either MPF files or folders of MPF files at the CRIPPA bender. VTube accepts UNC names as well as regular paths with drive letters.
   
   
5. Enter the IP address in the PING IP ADDRESS field if it is a fixed field. (This is not required. It allows VTube to ping the address to see if the network location is active before trying to open communications.)
   
   
6. Press Close to save the settings. VTube will save these values to a persistent configuration file that will not change unless you change them in this grid.

In the EXPORT menu, click on the CRIPPA MPF button.

Set the check boxes for the options you want to use, then press Build New Crippa MPF File.

If the path to the bender is not in the Path Manager list, then you can Add a New Persistent Path to find the path to the bender. If it is in the list, then double click on that path.

You can also send the new XYZ Centerline data from the VTube-LASER BENDER SETUP menu to the SOCO bender using the VTube Bender Output menu.

Enter the XYZ Screen At the SOCO Control

At the SOCO control, enter the XYZ Screen. With the XYZ Screen open, the SOCO control will understand that it must extract the MASTER XYZ data in the incoming data and import that into the SOCO NVS software.

Enter the BENDER SETUP menu in VTube-LASER

Follow these steps in the VTube-LASER:

Press the "BENDER SETUP button in the Navigation Pane.

STEP 1 - Set the correct bender number at the top of the window. As of version 2.7, the SOCO SVNet option is available - which means you should see a SOCO bender at the top left corner of the screen.

STEP 2 - On the right click on "Setup the Bender".

STEP 3 - Click on AUTO SEND

The SOCO will receive new data and ask if it should be imported with a dialog. Press YES to import the data.

At the SOCO Control

At the SOCO control, setup and bend the first tube through the YBC and then Compile Execution screen.

After Bending the Tube

After the bending cycle is complete, remove the tube from the dies. Leave the bender in AUTO mode.

Measure the tube with VTube-LASER

Measure and align the tube to determine if it qualifies by falling within the envelope tolerance for the tube shape.

In the VTube-LASER screen shot, you see the actual result of the first tube not qualifying in shape. The red cells in the tangent point grid on the lower left show that the measured tube centerline is out-of-tolerance.

Correct the SOCO with VTube-LASER - Enter BENDER SETUP

Follow these steps in the VTube-LASER:

Press the "BENDER SETUP button in the Navigation Pane.

RECALL SOCO YBC data and then SEND CORRECTIONS

STEP 1 - Set the correct bender number at the top of the window. As of version 2.7, the SOCO SVNet option is available - which means you should see a SOCO bender at the top left corner of the screen.

STEP 2 - If the Part Number is empty, then press the Copy the Master Part Setup values.

STEP 3 - Click on RECALL. This will update the BLUE columns in the Bender Setup.

STEP 4 - You can manually change the ADJUSTMENT values before sending corrections. In this case, we set the first and last Length adjustment to zero in order to keep the start position of the carriage in the same place.

STEP 5 - Click on AUTO SEND. This will send the ORANGE columns to the SOCO bender.

At the SOCO Bender - Press GO!

Press GO! The SOCO will compile the changes.

You will see a progress bar after you press GO!

The "Auto Compensation Completed" message will appear in the lower right corner.

Bend the corrected part now.

Measure at the VTube-LASER Computer

Measure and align the tube again to determine if it qualifies by falling within the envelope tolerance for the tube shape.

This screen shot shows an actual resulting change after the correction.