Difference between revisions of "VTube-LASER v2.8"
(→25px NEW: REPORT COMMANDS - Tangent Deviation AVERAGE and MAXIMUM Values) |
(→BUILD 11 - February 15, 2017) |
||
| Line 24: | Line 24: | ||
==[[image:Check.jpg|25px]] NEW: "Default Tolerance Ends" Value== | ==[[image:Check.jpg|25px]] NEW: "Default Tolerance Ends" Value== | ||
| + | |||
| + | <table cellpadding=10 width=900> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | The '''Default Tolerance Ends''' value is in the Inspection Data menu. | ||
| + | <br><br> | ||
| + | It allows you to set the end length default values separately from the tangent point / midpoint tolerance values. | ||
| + | <br><br> | ||
| + | <td> | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:vtl-v2.8_Default End Tolerance.png|400px]] | ||
| + | </tr> | ||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | |||
| + | ==[[image:Check.jpg|25px]] NEW: REPORT COMMANDS - Tangent Deviation AVERAGE and MAXIMUM Values== | ||
| + | |||
| + | <table cellpadding=10 width=900> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | Two new array values are available for reports: AVERAGE deviation and MAXIMUM deviation. | ||
| + | <br><br> | ||
| + | The new commands are | ||
| + | * <code>array_dev_tmt_average</code><br> | ||
| + | * <code>array_dev_tmt_maximum</code> | ||
| + | <br><br> | ||
| + | See the example result in the report on the right, and the report template source to create this table shown below.<br><br> | ||
| + | [[image:vtl-2.8_inspection data tangent average and maximum html sample.png|300px]] | ||
| + | |||
| + | <br><br> | ||
| + | |||
| + | |||
| + | <td> | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:vtl-2.8_inspection data tangent average and maximum.png|400px]] | ||
| + | </tr> | ||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | |||
| + | |||
| + | =BUILD 19 - February 22, 2017= | ||
| + | |||
| + | ==[[image:Check.jpg|25px]] ENHANCED: Winton WMC Communications== | ||
<table cellpadding=10 width=900> | <table cellpadding=10 width=900> | ||
Revision as of 23:21, 3 March 2017
|
Revision 2.8Release Date: Not Released
|
|
Contents |
BUILD 11 - February 15, 2017
NEW: "Default Tolerance Ends" Value
|
The Default Tolerance Ends value is in the Inspection Data menu.
|
|
NEW: REPORT COMMANDS - Tangent Deviation AVERAGE and MAXIMUM Values
|
Two new array values are available for reports: AVERAGE deviation and MAXIMUM deviation.
|
|
BUILD 19 - February 22, 2017
ENHANCED: Winton WMC Communications
|
The Default Tolerance Ends value is in the Inspection Data menu.
|
|
NEW: REPORT COMMANDS - Tangent Deviation AVERAGE and MAXIMUM Values
|
Two new array values are available for reports: AVERAGE deviation and MAXIMUM deviation.
|
|
Other Pages
- Back to VTube-LASER
- Back to VTube Software Updates (for LASER Mode)
- See also VTube-STEP
- See also VTube-STEP Revisions
- See VTube-LASER Customer Support Page to download the latest version.
- See VTube-LASER Cut Planes
- See the tutorial on DCP - Diameter Cut Planes
- See How to Measure Tubes Attached to an Evaporator with the DCP Feature
