Difference between revisions of "VTube-LASER Videos for FARO"
(Created page with "<table> <tr cellpadding=10> <td width=300> See a complete list of VTube-LASER videos on this page.<br><br> * Back to [http://www.advancedtubular.com/vtube-laser.htm the Main...") |
Revision as of 19:16, 25 January 2018
|
See a complete list of VTube-LASER videos on this page.
|
|
Version 2
Video 75: HOW TO USE ASSEMBLY CONTROL
| This video demonstrates the new ASSEMBLY CONTROL feature in version 2.9 of VTube-LASER. This feature allows you to import, measure, and align ANY number of tubes in one project. |
|
Video 74: HOW TO CONNECT VTUBE-LASER TO A FARO ARM
| This video shows how to connect to the FARO arm and access the FARO driver windows from inside VTube-LASER. |
|
Video 73: MEASURING TUBE WITH ARMOR
| Michael Cone shows how to setup VTube-LASER to measure tube with armor on the OD. |
|
Video 72: VTUBE-LASER CORRECTING AN AIM WIRE BENDER
| This video was created by AIM MACHINES. It shows a user correcting a wire bender with the FARO arm using our VTube-LASER software. |
|
|
Video 71: HOW TO COMPARE SOLID MODELS TO PRINT DATA
| This is a tutorial that shows how to compare solid models to print data to determine if they are the same part. |
|
Video 70: PROPER END-SCAN TECHNIQUE
| This is a tutorial that shows how to properly perform an end-scan with VTube-LASER. Follow these simple techniques to ensure that your end scans are reliable and accurate. |
|
Video 69: PATH MANAGER SEARCH AND MOVE
|
The PATH MANAGER is window that contains a list of paths that you want to access often in VTube-LASER. |
|
Video 68: RECALLING and SENDING DATA with ADDATA ZMODEM PROTOCOL
|
This is a 21-second video showing VTube-LASER communicating with a bender using the Addata ZModem protocol. First, do a RECALL to update BLUE bender data columns from the bender. Second, SEND the ORANGE columns with corrected data to the bender. |
|
Video 67: When to use UNISCAN and MULTISCAN Scanning Modes in VTube-LASER
| This video demonstrates how and why to switch from UNISCAN to MULTISCAN scanning modes and back. |
|
Video 66: VTube-LASER Speed Test - LOAD PROJECT - SCAN - REPORT
| This is a speed test on a 3 bend exhaust part. The goal is show how easy it is to load a project and scan it in order to get a report. |
|
Video 65: Introducton to the PRECISION WEIGHT CONTROL Alignment
| Precision Weight Control Alignment allows you to take-over the weighting of every straight section in a VTube-LASER tube. See how the feature works in this video. |
|
Video 64: Introduction to the DUAL CYLINDER FIT Feature for Scanning
| This video shows why the Dual Cylinder Fit feature is a ground-breaking addition to VTube-LASER. If you scan tube shapes, then you should upgrade to this version of VTube-LASER immediately. Watch the video to see why. |
|
Video 63: Quick Demo of ORBIT Control Window
| This is a quick demo of the ORBIT Control window that was released in version 2.8. |
|
|
Video 62: Setup and Correct SOCO Benders with VTube-LASER Communications
|
Created at Tube Form Solutions, this video demonstrates VTube-LASER being used to setup a SOCO bender from a solid model, then correcting the bend program through a network connection by measuring the tube shape and sending correction data to the bender. |
|
Video 61: Setup and Correct Alpine Benders with VTube-LASER Network Communications
|
Created at Elite Tube & Fabrication, this video demonstrates VTube-LASER being used to setup an Alpine bender from a solid model, then correcting the bend program through a network connection by measuring the tube shape and sending correction data to the bender. |
|
Video 60: Diameter Cut Plane - Quick Tutorial
|
Michael Cone explains the concept behind the DCP (Diameter Cut Plane) feature and demonstrates how it works. This is a new innovation added in version 2.6. |
|
Video 59: Diameter Cut Plane - Quick Demo
|
This video shows what you can do with the DCP (Diameter Cut Plane) feature added in version 2.6. With DCP, even if the laser stripe is crosses multiple straights at the same time, it finds and keeps the closest one - on-the-fly. It even filters out non-diameter objects that are behind the top diameter. |
|
Video 58: Speed Test - Reverse Engineer to SOLIDWORKS in Less than 60 Seconds
|
This video shows how fast VTube-LASER can reverse engineer a tube and build it in SOLIDWORKS - including BEND PROFILE measurements to measure the radius values. The version of VTube-LASER in this video is 2.5. |
|
Video 57: How To COMPLETELY Reverse Engineer a Tube with the New BEND PROFILE Feature
|
This video shows how to measure a bend profile to calculate the true radius during reverse engineering of a tube. The version of VTube-LASER in this video is 2.5. |
|
Video 56: How to Manually Setup for Measuring Split Bends from Traditional Part Data (180-Degree Bends)
|
This video shows how to setup Split Bend for measuring 180-degree bends from parts defined in prints. The version of VTube-LASER in this video is 2.5. |
|
Video 55: How to Use Bender Data to Setup the Master Part
|
Sometimes it's necessary to setup the master part from bender data rather than the normal solid model import or the manual entry of centerline XYZ coordinates. |
|
Video 54: How to Calibrate the FARO Probes in VTube-LASER
|
Calibrated FARO probes is a foundational skill that is critical for successful measurements. |
|
Video 53: Introductory Training in VTube-LASER Version 2
|
This video is designed for FARO account managers - but it's also good for customers with new users that need to learn how to use VTube-LASER. |
|
Video 51: Changing the Part Shape by Changing Bender Data
|
See how easy it is to quickly change the part shape by editing the bender data. |
|
Video 50: VTube User Interface Scan Sounds
|
This video shows VTube-LASER User Interface scan sounds. |
|
Video 49: Measuring a Tube Gauge
|
This video shows how to measure a tube gauge with VTube-LASER. |
|
Video 48: Reverse-Engineering Demonstrated
|
This video shows how to reverse engineer a tube shape with VTube-LASER. |
|
Video 47: MultiScan Measuring Technique
|
This video shows the MultiScan measuring technique. |
|
|
Video 46: How to Measure Straights With Brackets And Other Objects
|
This video shows how to scan around objects on a tube straight. |
|
|
Video 45: How to Measure Previous Straights Again
|
This video shows how repeat a measurement of previous straights. |
|
|
Video 44: Entering LRA Data to Establish the Master Data
|
This quick video shows how to enter LRA bender data to establish the MASTER data for a part. |
|
|
Video 43: Wire-form Measuring - 20-second Import and 16-second Measure
|
For applications that are time-critical, this video shows how VTube-LASER can import and measure tubes very quickly. |
|
Video 42: How To Use a Solid Model to Build VTube-LASER MASTER Data
|
Click on the image to see a video on how to build VTube-LASER MASTER data from a solid model |
|
Video 41: Winton Bender Corrections Loop Video
|
Click on the image to see a 60 second video on how correction loops work with the Winton RD bender: |
|
Video 40: Sixty Second SPLIT BEND Feature Demo
|
It's easy and it's accurate: VTube-LASER measures 180 degree bends using a very accurate and unique SPLIT BEND feature. |
|
Video 39: Measuring the Demo Tube 3 Radius With the Ball Probe
|
Measuring the radius with a ball probe is very consistent if done properly. |
|
|
Video 38: Measuring Demo Part 3 with the HD Scanner on a Table Surface
|
This is a quick video showing how to measure demo tube 3 on a table surface with the HD scanner. |
|
|
Video 37: Measuring Demo Part 3 with the HD Scanner in a Tube Clamp
|
This is a quick video showing how to measure demo tube 3 in a tube clamp with the HD scanner. |
|
|
Version 1.96
Video 35: The Difference Between End Length Adjustment and End Measured Offsets
|
This is a tutorial by the developer of VTube-LASER, Michael Cone. Michael explains the difference between the END LENGTH ADJUSTMENT values and the END MEASURED OFFSET values in the Part Setup menus. |
|
Video 34: Using Tube Data Storage Menu to Access Historical Data
|
This is a tutorial by the developer of VTube-LASER, Michael Cone. Michael will show you how use Tube Data Storage to permanently store historical data about every measure made by VTube-LASER. |
|
Version 1.94
Video 33: Reverse Engineering a Tube Using the Ball Probe
|
This is a tutorial by the developer of VTube-LASER, Michael Cone. Michael will show you how you can reverse engineer a tube with a FARO Edge arm and the ball probe. |
|
Video 32: The Benefits if Wide Diameter Scanning
|
This is a tutorial by the developer of VTube-LASER, Michael Cone. Michael will show you why wide diameter scanning is superior to other forms of scanning tubes. |
|
Video 31: How to Reverse-Engineer a Tube
|
This video shows how to reverse engineer a tube in VTube-LASER 1.94. |
|
Video 30: Springback Compensation Tutorial
|
This video shows how calculate the anticipated bend angle springback and then compensate the bend setup to make the first part shape close to the nominal shape. |
|
Other Pages
- See Retired VTube-LASER Videos
- Back to VTube-LASER
