Difference between revisions of "VTube Communications With Transfluid Benders"
(→STEP 5: tProject Updates) |
(→How to Send New Data to tProject from VTube-STEP) |
||
Line 172: | Line 172: | ||
===STEP 4: Send=== | ===STEP 4: Send=== | ||
Click Send to Bender. VTube will show "Send to Bender Complete" if it was able to save the output data for Transfluid. | Click Send to Bender. VTube will show "Send to Bender Complete" if it was able to save the output data for Transfluid. | ||
+ | </td> | ||
+ | <td width=300> | ||
+ | [[image:VTube-STEP_TransfluildSend.png|700px]]<br><br> | ||
+ | [[image:VTube-STEP_TransfluildSend_Dialog.png|700px]]<br><br> | ||
+ | </td> | ||
+ | </tr> | ||
+ | </table> | ||
+ | <table width=1000> | ||
+ | <tr valign=top> | ||
+ | <td width=300> | ||
===STEP 5: tProject Will Update=== | ===STEP 5: tProject Will Update=== | ||
tProject will display the new part immediately. | tProject will display the new part immediately. | ||
− | |||
===STEP 6: Save the tProject Project=== | ===STEP 6: Save the tProject Project=== | ||
It is important to save the new tProject project file using the disk button on the left. tProject does not automatically save the incoming data to disk. | It is important to save the new tProject project file using the disk button on the left. tProject does not automatically save the incoming data to disk. | ||
− | |||
− | |||
− | |||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
− | |||
− | |||
[[image:Transfluid_ReceivedNewData.png|700px]] | [[image:Transfluid_ReceivedNewData.png|700px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
+ | |||
<br><br> | <br><br> |
Revision as of 21:06, 29 March 2021
This page describes the use of the VTube-LASER to Transfluid bender corrections. |
Back to VTube-LASER
Contents |
CONFIGURING VTUBE-STEP AND VTUBE-LASER for COMMUNICATIONS with TRANSFLUID tPROJECT
As of version 3.0 build 456, we've embedded the Transfluid SVNET protocol in VTube-STEP and VTube-LASER.
You can set this protocol in the Benderlink setup grid in System Options.
You can perform this setup from VTube-STEP or VTube-LASER. The steps are identical in both.
STEP 1: Enter the SYSTEM OPTIONS Menu in VTube
|
STEP 2: Setup the Benderlink Network Grid for Transfluid Supravision Network Protocol
|
CONFIGURING TRANSFLUID TPROJECT FOR COMMUNICATIONS WITH VTUBE-LASER AND VTUBE-STEP
Follow these steps in Transfluid tProject to set up communications for VTube-LASER and VTube-STEP |
tProject Configuration STEPS
STEP 1: Enter Options Window
Click on the blue button wrench/screwdriver button in the upper right corner of the user interface. |
STEP 2: Enter the Import/Export Tab
Click on the Import/Export tab. |
STEP 3: Set the Import Box Settings
Enter the set up data in the Import box.
|
STEP 4: Check for a Green LED in the Main User Interface
Close the options menu with the OK button and check for the Supravision communications LED in the lower right corner of tProject. The LED should be green. |
How to Prepare tProject to Receive New Data from VTube
The Transfuild tProject program can receive data for a part that has never been sent to it before from VTube-STEP. STEP 1: Clear the tProject ProjectSTEP 2: DO NOT Enter a Project NameThis allows VTube to control the new incoming name. STEP 3: Click on OK |
How to Send New Data to tProject from VTube-STEP
The Transfuild tProject program can receive data for a part that has never been sent to it before from VTube-STEP. This allows a user to import a solid model of any tube, then send it to tProject. STEP 1: Import the ModelImport the part using standard VTube-STEP procedures STEP 2: Bender Output MenuClick on the Bender Output button in the navigation pane. STEP 3: Bender NumberSelect the bender number for the Transfluid bender. STEP 4: SendClick Send to Bender. VTube will show "Send to Bender Complete" if it was able to save the output data for Transfluid. |
STEP 5: tProject Will UpdatetProject will display the new part immediately. STEP 6: Save the tProject ProjectIt is important to save the new tProject project file using the disk button on the left. tProject does not automatically save the incoming data to disk. |
Other Pages
- See VTube-LASER
- See VTube-STEP