Difference between revisions of "Benderlink for SolidWorks"
(→Software Updates) |
(→Software Updates) |
||
| Line 36: | Line 36: | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr><td>Screen Shot</td><td width="100">Date Released</td><td width="100">Link to Page</td><td>New Features</td></tr> | <tr><td>Screen Shot</td><td width="100">Date Released</td><td width="100">Link to Page</td><td>New Features</td></tr> | ||
| − | <tr><td>[[Image:Blinksw_1_9.jpg|100px]]</td><td>April 4, 2009</td><td>[[Benderlink for SolidWorks 1.9]]</td><td>Support for TAURING CNC output | + | <tr><td>[[Image:Blinksw_1_9.jpg|100px]]</td><td>April 4, 2009</td><td>[[Benderlink for SolidWorks 1.9]]</td><td>Support for TAURING CNC output</td></tr> |
<tr><td>[[Image:Blinksw_1_8.jpg|100px]]</td><td>March 24, 2009</td><td>[[Benderlink for SolidWorks 1.8]]</td><td</td></tr> | <tr><td>[[Image:Blinksw_1_8.jpg|100px]]</td><td>March 24, 2009</td><td>[[Benderlink for SolidWorks 1.8]]</td><td</td></tr> | ||
<tr><td>[[Image:Blinksw_1_8.jpg|100px]]</td><td>March 10, 2009</td><td>[[Benderlink for SolidWorks 1.73]]</td><td></td></tr> | <tr><td>[[Image:Blinksw_1_8.jpg|100px]]</td><td>March 10, 2009</td><td>[[Benderlink for SolidWorks 1.73]]</td><td></td></tr> | ||
Revision as of 13:24, 7 April 2008
Benderlink for SolidWorks software is designed to convert from SolidWorks to bender data then to connect SolidWorks workstations to SVNET-based benders.
If a measuring center arm is setup to sketch a 3D centerline of a measured tube shape, then Benderlink will help you reverse-engineer tube shapes, and assist in correcting the bender's data.
Contents |
Features
The main features of this software:
- - Read tube data from SolidWorks
- - Convert the tube data to bender data
- - Save / Recall the bender data
- - Program and calculate cut-length to remove elongation using the Bend Reduction Editor
- - Program and calculate last length to remove elongation using the Bend Reduction Editor
- - Send new nominal data to benders that support SVNET protocol.
- - With a measuring center: Make and send correction data to benders that support the SVNET protocol.
- - With a measuring center: Reverse-engineer tube shapes
- - Reverse tube feature that allows for reversing the end A for end B.
The reverse-engineering feature is performed by using 3D sketch with a measuring center - like a FARO arm. The tube centerline is sketched in 3D, then transferred to Benderlink for SolidWorks.
The correction feature is performed by measuring a tube with FARO arm, using this data to create a tube centerline in SolidWorks, then allow Benderlink to compare this inspected data with the MASTER data.
Software Updates
| Screen Shot | Date Released | Link to Page | New Features |
| April 4, 2009 | Benderlink for SolidWorks 1.9 | Support for TAURING CNC output |
 | March 24, 2009 | Benderlink for SolidWorks 1.8 | <td</td>
