Difference between revisions of "CNC Bender v11-20081230"
| Line 35: | Line 35: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:180pipe_chrome.jpg| | + | [[image:180pipe_chrome.jpg|500px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 44: | Line 44: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:cncbender_xyzpage_180pipe.jpg| | + | [[image:cncbender_xyzpage_180pipe.jpg|500px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 55: | Line 55: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:cncbender_frbpage_180pipe_nocombine.jpg| | + | [[image:cncbender_frbpage_180pipe_nocombine.jpg|500px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 66: | Line 66: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:cncbender_combinevariables.jpg| | + | [[image:cncbender_combinevariables.jpg|500px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 75: | Line 75: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:cncbender_frbpage_180pipe_combine.jpg| | + | [[image:cncbender_frbpage_180pipe_combine.jpg|500px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 84: | Line 84: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:cncbender_180pipe.jpg| | + | [[image:cncbender_180pipe.jpg|500px]] |
</td> | </td> | ||
</tr> | </tr> | ||
Revision as of 03:46, 31 December 2008
NEW - HITCH FEED Push Bending
CNC Bender can now hitch feed during push bend to create a helical tube shape with many loops from a material that is much longer than the bender.
NEW - Push Bend Twist GEARING
CNC Bender now gears the rotational twist motion to the feed motion in order to create more accurate helical shapes. As the Feed axis moves forward, the Rotation axis rotates at a pre-programmed gear ratio in the Push Bending Profile page.
NEW - Automatic Bend Combine During XYZ to FRB Conversion
CNC Bender now allows you to automatically combine adjacent bends into a single bend if the adjacent bends meet a preprogrammed criteria controlled by the Low Level dynamic options.
This feature is important because centerline XYZ data always represents bends that approach and exceed 180 degrees as two separate adjacent bends.
|
This part was drawn in SolidWorks and extracted by Benderlink for SolidWorks into XYZ data. |
|
|
The data was imported into the XYZ data page of CNC Bender. |
|
|
When XYZ to FRB conversion is made without the Combine Bends feature enabled, the result is five bends as shown in this FRB page.
|
|
|
Enter the Low Level menu. The Combine Bends feature is enabled in the dynamic options.
|
|
|
When XYZ to FRB conversion is made again, there will be only 3 bends in the FRB data. Four of the bends were combined into two bends. See the first two bend angles. |
|
|
This is the resulting image in CNC Bender Bender Data menu: |
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- Read about Push Bending
- Read about Push Bend Profile Tables
