VTube Software Updates

See a complete list of VTube updates on this page.

March 15, 2012	VTube-LASER v1.76	Coping layout feature
February 9, 2012	VTube-LASER v1.75.4	Merge bends feature
February 7, 2012	VTube-LASER v1.75.3	Automatic Closeup of Last Measure feature.
February 2, 2012	VTube-LASER v1.75.1	Page numbers are added to bottom of report. Fix to move to previous when remeasure.
January 15, 2012	VTube-LASER v1.75	Scanner setup save to project is enhanced. The cylinder fit tolerance qualification is enhanced for better measuring experience. New cylinder fit error checks are added to assure good measurements.
January 5, 2012	VTube-LASER v1.74	Scanner setup is now saved with the project file. It is now possible to skip either end measurement. The end-scan qualification logic is improved.

October 19, 2011	VTube-LASER v1.73	Fine tuning for FARO Edge arm. The Cut Plane offset value is now displayed in interface. Cut Plane offset is now adjustable without remeasure. Sounds trimmed so that they play for shorter times.
October 10, 2011	VTube-LASER v1.72	Deep scanning with up to 200 stripes per straight now allowed.
October 4, 2011	VTube-LASER v1.71	New transparent envelope models.

September 20, 2011	VTube-LASER v1.70	Enhanced the accuracy of inspection mathematics in special situations.
September 1, 2011	VTube-LASER v1.69	Enhanced Measure Setup menu links to more Faro menus. New report values show arm and probe values like calibration dates, 2 sigma values. VTube-LASER Programmer license mode.
August 8, 2011	VTube-LASER v1.68	New Excel report builder, revised Overbend calculator, new options in the Bender Setup screen, new tab menus in Master data.
July 18, 2011	VTube-LASER v1.67	New Split Bend for precisely splitting angles that approach and exceed 180 degrees. New connect and disconnect from the arm.

May 27, 2011	VTube-LASER v1.66	New save changes dialog, in-process bend angle correction
May 19, 2011	VTube-LASER v1.65	Increased the accuracy of the radius stripe scan method for measuring bend radii, enhanced the Winton bender protocol, added invert rotation check boxes to the bender setup page, added new report charts
May 10, 2011	VTube-LASER v1.64b	Added Transfluid bender communications, added new radius stripe scan method for measuring bend radii
April 6, 2011	VTube-LASER v1.63d	Resolved issue with end-scan qualification with ball probe

March 31, 2011	VTube-LASER v1.63	Choose from multiple custom reports on the screen. Add and edit custom report templates to VTube-LASER.
March 11, 2011	VTube-LASER v1.62	End scan qualifications are much faster, new progress dialog for when end-scan is taking more time with new process cancel button
March 04, 2011	VTube-LASER v1.61	New end labels identify the ends of the tube and automatic diameter handling fixes
February 21, 2011	VTube-LASER v1.6	Important end-scan outlier point detection and prevention, continuous tactile scan, faster redraws, improved user interface
February 7, 2011	VTube-LASER v1.59	Ball probe measurements and laser measurements now work properly together in the same tube measure.
January 18, 2011	VTube-LASER v1.58	New "Construct Tube" feature that allows users to route a tube in 3D space by pointing the arm, increase or decrease points and straights on the fly when measuring tubes
January 13, 2011	VTube-LASER v1.57	Supravision Import, faster alignment, improved Bender Setup, many other changes
January 6, 2011	VTube-LASER v1.56	New springback compensation variables, new items in the inspection report - like the new XYZ deviation report, bender data setup menu enhanced, invert rotation feature
January 3, 2011	VTube-LASER v1.55	New enhanced radius measurement