Difference between revisions of "CNC Bender"
From ATTWiki
(→Software Updates) |
(→Software Updates) |
||
| Line 94: | Line 94: | ||
<tr><td>March 30, 2007</td><td>[[CNC Bender ProControl 10-20070330]]</td></tr> | <tr><td>March 30, 2007</td><td>[[CNC Bender ProControl 10-20070330]]</td></tr> | ||
<tr><td>March 15, 2007</td><td>[[CNC Bender ProControl 10.0.6.2]]</td></tr> | <tr><td>March 15, 2007</td><td>[[CNC Bender ProControl 10.0.6.2]]</td></tr> | ||
| − | <tr><td>November 6, 2006</td><td>[[CNC Bender ProControl 10.0.6.0]]</td></tr> | + | <tr><td>November 6, 2006</td><td>[[CNC Bender ProControl 10.0.6.0j]]</td></tr> |
| + | <tr><td>October 27, 2006</td><td>[[CNC Bender ProControl 10.0.6.0i]]</td></tr> | ||
</table> | </table> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
July 17, 2006<br> | July 17, 2006<br> | ||
Revision as of 22:21, 3 October 2007
Contents |
FAQ
- What is Manual Mode?
- What is Auto Mode?
- What is Step Mode?
- What is Auto Build?
- What is a Run List?
- What is a Process List?
- What is Safe Mode Cycle Hold?
- What is Zero Energy State?
- What is Safe Mode Motion Auto Recovery?
- What is Master Power On?
- What is the CNC Processor?
- Can Master Power Be Kept ON by CNC Bender?
- Do you support Feed Boost Benders?
- What is a CIO Object?
- What is the CIO Editor?
- Show me the CNC Bender Operator Station
- What are the CNC Bender Versions?: ProControl and LiteControl
- What is the CNC Bender Upgrade Service?
- Do you offer CNC Bender training? See - CNC Bender Training Service
Tutorials
- How Do I Make A Dynamic Option Invisible?
- How Do I Install CNC Bender On a New Computer?
- How do I use the Post Fault Processlist?
- How do I use the Post Halt Processlist?
- Restoring the Configuration File in CNC Bender
- About the Constant On Button
- Ideas for SMT Bend Machine Optimization
- Ideas for CNC Bender Bend Program Optimization
- Preventing master power shutdown during processlist building. See Output Sustain in Seconds
Diagnostics
Diagnostic Steps for Master Power On Problems
General Information
- CNC Bender Technical Document Library
- About Top Hats (Schneider Momentum Ethernet Adapters)
- About Pressure Die Boost
- About Dynamic Options
- About Minuteman UPS used in the ProControls
- About MODBUS Protocol
- MODBUS Exception Responses List
Downloads Related to CNC Bender
Download Top Hat Setup Software for Top Hat setup
Download I2T HMI Software
Download Minuteman UPS PowerCenter Software - Uninterruptible Power Supply administrative software
Configuration
About main.axislist file
About CNCProcessor.cfg file
Processlists: Configuring the InitAxes Processlist
Software Updates
| October 3, 2007 | CNC Bender v10-20071003 |
| September 28, 2007 | CNC Bender v10-20070928 |
| September 20, 2007 | CNC Bender v10-20070920 |
| September 14, 2007 | CNC Bender v10-20070914 |
| August 28, 2007 | CNC Bender v10-20070828 |
| August 3, 2007 | CNC Bender v10-20070803 |
| July 26, 2007 | CNC Bender v10-20070726b |
| July 11, 2007 | CNC Bender v10-20070711 |
| July 5, 2007 | CNC Bender v10-20070705 |
| July 2, 2007 | CNC Bender v10-20070702 |
| March 30, 2007 | CNC Bender ProControl 10-20070330 |
| March 15, 2007 | CNC Bender ProControl 10.0.6.2 |
| November 6, 2006 | CNC Bender ProControl 10.0.6.0j |
| October 27, 2006 | CNC Bender ProControl 10.0.6.0i |
July 17, 2006
Version 10.0.5.9 Released - Axis Enable Delay After Cycle Start is added. This feature delays the moment of ENABLE by a millisecond value in order to give the axis drives time to boot.
May 15, 2006
- CNC Bender 10.0.5.7e - Dynamic Correction - This new feature allows for real-time correction and adjustment of the bender for each part.
- CNC Bender 10.0.5.7e - New Graphic Window - Now handles bends equal to or greater than 180 degrees
- CNC Bender 10.0.5.7e - Auto Dynamic Option Update - Easier automated update process
